|
|
MP1401
400-470MHz
Cost-Effective Wireless Solutions |
|
|
|
|
|
|
|
|
MP1401
400-470MHz
Cost-Effective Wireless Solutions |
|
|
|
|
|
|
The MP1401 is a fully synthesized 800 channel miniature UHF transceiver featuring the very latest in RF design techniques and components. Specifically designed and optimised for the reception of audio bandwidth data, it is used in OEM equipment to provide a half-duplex wireless data link.
An I2C bus is used to control all transmitter and receiver functions including frequency selection, transmitter-receiver switching and power control.
Offering the ultimate in user flexibility and configuration options, the combination of synthesizer and I2C control allows an elegant and cost-effective solution to radio telemetry system design.
The receiver utilises low power consumption circuitry throughout to minimise current drain. Fast turn-on and off times allow power strobing to further enhance power drain.
The receiver performance, being the major factor in achieving good radio ranges, has been optimised by use of high quality miniature helical filters and high specification crystal filters. The receiver exhibits excellent sensitivity even when subjected to high level unwanted signals.
Orders should specify in which country the units are to be used.
This model is also available in transmitter-only and receiver-only versions.
A range of modem boards is available to allow RS232 data streams to be sent.
|
Technical Details |
||
|
General |
||
|
Alignment Range |
400-470MHz |
|
|
Switching Range |
10MHz |
|
|
Operating Temperature |
-30 to +60°C |
|
|
Channel Spacing |
12.5kHz (25 & 50kHz options available) |
|
|
Modulation |
Narrow band angle modulation |
|
|
Frequency Error |
2.5ppm over -30 to +60°C |
|
|
Audio bandwidth |
300-3000Hz |
|
|
Supply Voltage |
5V ±5% |
|
|
Dimensions |
79 x 64 x 15mm exc. connectors |
|
|
Humidity |
95% RH, non-condensing |
|
|
Shock |
BS2011 Part 2.1Ea, 30g 18ms |
|
|
Vibration |
BS2011 Part 2.1Fd Region A, Cat. 4, 10-1000Hz for 1 hour |
|
|
Acceleration |
BS2011 Part 2.1Ga, ±4g any axis |
|
|
Specification Compliances |
ETS 300 113, ETS 300 220, FCC Part 90 |
|
Technical Details |
||
|
Transmitter Section |
||
|
RF Output Power |
500mW (others selectable) |
|
|
Modulation Level |
±2.0kHz at 1kHz |
|
|
Adjacent Channel Power |
<-65dBc |
|
|
Spurious Emissions |
<-36dBm |
|
|
Current Consumption |
350mA typ. at 500mW output (VSWR1.5) |
|
|
TX risetime |
<16ms |
|
Technical Details |
||
|
Receiver Section |
||
|
Sensitivity |
-118dBm for 12dB SINAD |
|
|
Adjacent Channel Selectivity |
65dB |
|
|
Intermod. Response Rejection |
65dB (70dB available on special order) |
|
|
Blocking |
88dB |
|
|
Spurious Response Rejection |
70dB |
|
|
Spurious Emissions |
<-57dBm |
|
|
Co-Channel Rejection |
-8dB |
|
|
Mute |
Fitted as standard (may be removed) |
|
|
RX risetime |
<16ms |
|
|
RX mute lift |
<3ms |
|
|
Current Consumption |
35mA |
|
Technical Details |
||
|
Connections |
||
|
1 |
+V |
5V Positive supply |
|
2 |
SCL |
I2C clock |
|
3 |
TXA |
TX audio input, 500mV rms |
|
4 |
0V |
Ground, negative supply |
|
5 |
RXA |
RX audio output, 150mV rms |
|
6 |
/CD |
RX carrier detect, TTL active low |
|
7 |
SDA |
I2C data |
|
8 |
- |
No pin (for connector polarity) |
|
9 |
RSSI |
Received Signal Strength Indicator |
|
10 |
Spare |
|
|
Coaxial MCX |
50 ohm antenna connection |
